Are You Looking for Mind Blowing Refinishing Services without Stressing About Your Bathtub Refinishing Peeling?
Poor workmanship and low quality products can be the reason for your bathtub refinishing peeling. At the point when unpracticed contractors are welcomed into your home or business your bathtub could experience the ill effects from bathtub glaze peeling around the drain and overflow.
The key to any successful refinishing project is the preparation, If your contractor happens to skimp on this step you have entered yourself into the bathtub peeling danger zone.
Removing the peeling coating is not an easy task using an orbital sander or paint stripper is the only way how to remove bathtub refinishing from your tub surface and a lot of contractors aren’t knowledgeable about bathtub peeling repair.
Some won’t remove the majority of the current coating from your tub which will cause another failure in a short period. For your bathtub to be durable with a long-lasting surface every bit of the old coating must be removed so that the new finish will adhere to the tub which will prevent bathtub refinishing peeling from happening.
I know many bathtub refinishing contractors make you wish you knew how to refinish a bathtub yourself. Take this for an example. Roughly 12 years prior I had a sweet more established woman call me by the name of Debbie Carter the primary thing she said before I could even get my first words out was “my bathtub is peeling” I delayed for a moment to tune in to each worry she had, the one thing that emerged the most was her getting some information about which kit is the best to purchase at Lowe’s that can cover up the chaos that the previous re finisher made.
I huffed, on the grounds that I knew there wasn’t a cheap solution to her issue however I couldn’t come straight forward and say STOP HIRING CHEAP BATHTUB REFINISHING CONTRACTORS, so I explained my process and the steps I take, and she flat out said that the other contractor literally came in with a paint tray, a paint roller some materials already prepared and started rolling within the first 15 minutes of arriving.
Hearing that left me disgusted and amazed, practically like a smack to my face and I never met the re finisher a day in my life.
In the wake of doing a profound careful review of what caused her bathtub coating to fail, I found that the reason for her bathtub refinishing peeling was delamination, the top coat of the surface failed because the tub was cleaned poorly where it could not adhere to the surface correctly.
How to Remove Old Paint From Bathtub so That it Can be Refinished Again?
The bathtub peeling repair process can be extremely confusing and dangerous if your not experienced to deal with it accurately. Bathtub strippers contain Methylene Chloride which has caused numerous deaths of unpracticed contractors in the bathtub refinishing industry so it is smart to hire an expert to deal with your task.
Materials that you will need:
- A decent quality stripper, for example, klean — Strip.
- Heavy duty solvent resistant latex gloves
- A paint brush
- A fresh air breathing system (this is vital).
- Shop vac
- Masking paper
- Masking tape
- Running water
- Industrial strength cleaner
- Exhaust fan
- Paint scraper
- Scraper blades
Step 1
Set up your exhaust fan and run it out of the nearest window
Step 2
To start the procedure you will need to clean the tub to remove any unwanted junk on the surface. (for every step I recommend using your Heavy duty solvent resistant latex gloves).
Step 3
Allow surface-to-air dry or you can use a heat gun to help dry surface quicker.
Step 4
After the tub is dry, mask off the floor and any surrounding areas that may get harmed.
Step 5
Set up your fresh air breathing system.
Step 6
Turn on fresh air breathing system and apply a generous amount of klean — Strip stripper or a stripper of your choice. Apply stripper by using paint brush. Swipe the stripper in to one side for best results. (always make sure your mask have been fit tested before use).
Step 7
After paint has started to wrinkle give the stripper a chance to sit on the tub surface for 25-30 minutes.
Step 8
Utilizing your paint scraper and scraper blades scrap off all free paint and dismiss by using a shop vac. (repeat steps 6 and 7 until no paint is no longer remaining on the surface).
Step 9
After all paint is removed clean the surface with industrial strength cleaner (you should clean tub no less than twice but I recommend 3 to 4 times after stripping).
Step 10
Give the tub a chance to air dry and plan for the refinishing process.
Using the correct procedures for bathtub refinishing peeling will bring about a dependable durable finish. Try not to wind up committing the same mistake as Debbie Carter by allowing unpracticed refinishers to hone on your bathtub. There are different methods for stripping your bathtub. Furthermore, this 10 step method won’t work if you’re thinking of removing paint from fiberglass tub this is particularly for porcelain, ceramic and cast iron tubs.
Is your bathtub refinishing peeling? Is it accurate to say that you are endeavoring to prevent it before it happens? Contact the experts at (423) 612-4174. Miraculous Makeovers goes above and beyond with our preparation to give you a long-lasting durable finish.
